Slope explained: degrees, percent, ratio and roof pitch
Updated November 16, 2026 · Pelantar team
Slope appears in many forms: percent on road signs, ratios on ramp specifications, degrees on a protractor and pitch on a roof. They all describe the same thing. This guide shows how they relate and where each is used, with the bubble level to help.
The four ways to describe slope
- Percent: rise ÷ run × 100. A 5% slope rises 5 units for every 100 units of run.
- Ratio: written 1:n, one unit of rise for every n of run. 1:20 is 5%.
- Degrees: the angle from horizontal, arctan(rise ÷ run).
- Pitch: roofing often uses rise per 12 units of run, so a 6/12 roof rises 6 inches for every 12 inches.
Handy conversions
- 1° is about 1.75% (1 : 57).
- 2% is about 1.15° (1 : 50).
- 5% is about 2.86° (1 : 20).
- 1:12 is 8.33% or 4.76°.
- 10% is about 5.71°.
- 30° is about 57.7%.
- 45° is exactly 100% (1 : 1).
- A 6/12 roof pitch is about 26.6°.
Percent and degrees are not the same
Small angles look similar in both units, but they diverge as slopes get steeper. 100% is 45°, not 90°. A vertical wall has an infinite percent slope. Whenever you read a gradient, check which unit is meant.
Common uses
Wheelchair ramps are often limited to 1:12 (8.33%) in accessibility guidance, with gentler slopes preferred. Drainage typically needs a small fall, often around 1 to 2%, so water runs away from a building or along a gutter. Check your local rules for exact requirements. Roads are signed in percent, while roof framing is described in pitch.
Measuring the slope you have
- Lay the phone on the surface in the bubble level and read the tilt in degrees.
- The results panel also shows percent, millimetres per metre and inches per foot.
- Use the conversions above to turn that angle into a percentage, a ratio or a roof pitch.
Phone sensors are accurate to roughly half a degree, which is about 0.9%, so use a proper level for jobs with tight tolerances.
Quick reference table
| Degrees | Percent | Ratio (rise : run) | mm per metre |
|---|---|---|---|
| 0.5° | 0.87% | 1 : 115 | 8.7 |
| 1° | 1.75% | 1 : 57 | 17.5 |
| 2° | 3.49% | 1 : 29 | 34.9 |
| 4.76° | 8.33% | 1 : 12 | 83.3 |
| 10° | 17.6% | 1 : 5.7 | 176 |
| 26.57° | 50% | 1 : 2 (6 in 12) | 500 |
| 45° | 100% | 1 : 1 | 1000 |
The formulas
Percent slope is tan(angle) × 100. The angle in degrees is the arctangent of rise divided by run. A ratio of 1 : n has a percent slope of 100 divided by n. A roof pitch of x in 12 has a slope of x ÷ 12, so 6 in 12 is 50% and about 26.6 degrees.
Common limits and standards
Accessible ramps in many countries are limited to a slope of 1 : 12, which is 8.33% or about 4.8 degrees, with landings at regular intervals. Drainage pipes typically need a fall somewhere between 1 : 40 and 1 : 100 depending on pipe size and local rules, while open surfaces usually need at least about 1% so that water does not pond. For roofs, standard asphalt shingles are usually installed at pitches of 4 in 12 or steeper, with special underlayment allowed on shallower roofs, and metal roofs can go lower. Always check your local code and the manufacturer instructions.
Why percent and degrees diverge
Percent slope and degrees are not proportional. A 45-degree slope is 100%, but a 90-degree wall is infinitely steep. That is why readings above about 60 degrees are not shown as percent slopes in the bubble level.
Measuring a slope yourself
Place a phone on the surface and read the tilt from the bubble level, or use the protractor on camera on a photo of the profile. Then use the table above to convert.
Frequently asked questions
How do I convert degrees to percent slope?
Take the tangent of the angle and multiply by 100. For example, tan(10°) × 100 is about 17.6%.
What is a 1:12 slope in degrees?
About 4.76 degrees, or 8.33%. It is a common maximum for accessible ramps.
What is a 6:12 roof pitch?
A roof that rises 6 inches for every 12 inches of horizontal run. It is a 50% slope and about 26.6 degrees.
Is a 100% slope vertical?
No. A 100% slope is 45 degrees, where rise equals run. A vertical surface is infinitely steep.
What slope do drains need?
Surface water usually needs at least about 1%, and drain pipes typically need a fall between 1 : 40 and 1 : 100 depending on size. Follow your local code.
Try the tools
Bubble Level · Online Protractor · Unit Converter