How accurate is a phone bubble level, and how to improve it
Updated November 16, 2026 · Pelantar team
A phone can work as a bubble level because it contains motion sensors. This guide explains what those sensors measure, how accurate they are, and how to get the best result from the Pelantar bubble level.
How a phone senses tilt
An accelerometer measures the direction of gravity relative to the phone. A gyroscope measures how fast the phone rotates. The browser combines them into orientation angles, and the level tool reads those angles to draw the bubble.
What accuracy to expect
Typical phone sensors are accurate to about 0.5°. On a one-metre shelf, 0.5° is a difference of about 8.7 mm between the two ends. For hanging a picture that is usually fine. For laying floor tiles or installing a kitchen worktop, use a proper level.
One view, three bubbles
The circular bubble shows tilt in both directions, the horizontal bubble shows left–right tilt and the vertical bubble shows front–back tilt. Lay the phone flat on a surface, stand it on its edge against a shelf, or hold it upright against a wall. All three bubbles respond at once, and the panel reports the tilt in degrees, percent and millimetres per metre.
How to zero the level
- Put the phone on a surface you can check by turning the phone.
- Note the reading, then rotate the phone 180° in the same place.
- If the two readings are opposite, the surface is tilted by half the difference. If they are the same, the sensor has an offset.
- Tap Zero here when the phone is on a surface you know is flat.
Tips for better results
- Remove thick cases, which can sit unevenly.
- Keep the phone away from a charging cable that props it up.
- Wait a second or two for the bubble to settle.
- Check the surface at two positions to catch a twisted shelf.
Converting tilt to slope
- 0.5° is about 0.9%, or 8.7 mm per metre.
- 1° is about 1.7%, or 17.5 mm per metre.
- 2° is about 3.5%, or 34.9 mm per metre.
The results panel shows these numbers for you, including inches per foot.
Comparing a phone with a real spirit level
A good carpenter's level resolves about 0.5 mm per metre, which is roughly 0.03 degrees. A phone is around 15 times coarser. That still makes it fine for hanging a shelf, levelling a washing machine or checking a tripod, but not for setting out a foundation or aligning machinery.
What affects phone accuracy
- Sensor offset. Each accelerometer has a small bias, which zeroing removes.
- The phone case. A case or camera bump that does not sit flat will tilt the whole phone.
- Movement. The sensor feels vibration as well as gravity, so let the reading settle.
- Temperature. Large temperature swings can shift sensor readings slightly.
- Flatness of the phone. Slightly bent phones lose accuracy when measured from the back.
Check your level with the flip test
Place the phone on a surface and note the reading. Rotate it 180 degrees in place and read again. If the two readings are equal and opposite, the surface is tilted by half the difference and the phone is accurate. If both show the same value, the phone has an offset, and you can remove it with Zero here.
Using the camera level on walls
The camera level draws a true horizontal line over the live camera view, which is useful for shelves, pictures and tile lines you cannot rest the phone on. Hold the phone upright, keep the lens square to the wall, and the line will show the horizon regardless of how the picture is framed.
Zero point and vibration
You can move the zero point to any surface you trust with the Zero here button, and a short vibration tells you when the level reaches it, so you can watch your work instead of the screen. Vibration works on most Android browsers.
Frequently asked questions
How many degrees is a level surface?
Zero degrees in both directions. A tilt of one degree is about 17.5 mm of rise per metre.
Why does my phone show 0.3 degrees on a flat table?
Either the table is not exactly level or the phone has a small sensor offset. Rotate the phone 180 degrees and compare. If both readings are the same, tap Zero here.
Can I use a phone to level a camera tripod?
Yes. Place the phone on the tripod head and adjust the legs until the bubbles centre, then remove it.
Does the level work with a case on?
Yes, but only if the case sits flat. Thick, uneven cases add error, so zero the level with the case on.
Why does vibration not work?
Some browsers, especially on iPhone, do not allow websites to vibrate the device. Android browsers usually do.
Try the tools
Bubble Level · Bubble Level on Camera