Can a phone measure decibels accurately?
Updated November 16, 2026 · Pelantar team
A phone can give a useful estimate of how loud a place is, but it is not a certified sound level meter. This guide explains what the Pelantar sound meter measures, what limits its accuracy, and when to use something better.
What a decibel is
A decibel (dB) is a logarithmic unit. Every increase of 10 dB is a sound that carries ten times more energy and is perceived as roughly twice as loud. Sound pressure level (dB SPL) is referenced to the quietest sound people can hear, so 0 dB SPL is near the threshold of hearing.
Why phones are not meters
- No absolute reference. A phone microphone measures signal level, not pressure, so the number depends on the model.
- Automatic processing. Many phones apply gain control and noise suppression to favour speech.
- Limited range. Very loud sounds clip and very quiet sounds disappear into microphone noise.
- No weighting. Professional meters apply A-weighting to match how the ear responds. The Pelantar meter is unweighted.
Typical levels for reference
- 30 dB: a quiet bedroom at night.
- 60 dB: normal conversation.
- 70 dB: a busy office or a vacuum cleaner at a distance.
- 85 dB: heavy traffic. Hearing authorities such as NIOSH recommend limiting exposure to 85 dBA over eight hours.
- 100 dB or more: power tools and concerts, where hearing damage can occur within minutes.
Getting the best reading
- Hold the phone steady with the microphone facing the sound.
- Keep your hand off the microphone opening and avoid wind.
- Let the reading settle for a few seconds before comparing.
- Use the dB offset if you have a reference meter, to match the two.
Reading frequency and note
The meter also finds the strongest frequency between 20 Hz and 8 kHz. A hum near 50 or 60 Hz often points to electrical equipment, and the note name with its cents offset helps when tuning an instrument.
When to use a calibrated meter
For workplace noise assessments, legal disputes, neighbour complaints that may go to a regulator, or hearing-protection decisions, use a calibrated Class 1 or Class 2 sound level meter. Use the phone to compare rooms, find the loudest appliance, or see how a change affects the noise.
A-weighting and C-weighting
Official noise measurements use frequency weighting to mimic human hearing. A-weighting reduces the influence of very low and very high frequencies and is the standard for workplace exposure, quoted as dBA. C-weighting is flatter and is used for peaks. Pelantar reports an unweighted level because it cannot apply a calibrated weighting to an uncalibrated microphone, so numbers will not match a weighted sound level meter exactly, especially for sounds with a lot of low-frequency energy.
Automatic gain and clipping
Many phones adjust microphone gain automatically to keep voices at a steady level. That is useful for calls but disastrous for measurement, because it flattens the differences you want to see. Browsers can request that this be turned off, and Pelantar does so, but some phones ignore the request. Very loud sound can also overload the microphone and distort, so readings above about 100 dB are unreliable.
How to get a better estimate
- Compare against a reference meter once and set the offset in Settings.
- Place the phone at ear height and about an arm's length from the source.
- Run the 20-second test several times and use the average.
- Keep your hand off the phone, because handling noise adds low-frequency sound.
What a phone is good for
Comparing rooms, finding the noisiest appliance, checking whether noise changes after moving a speaker, and learning how loud everyday sounds are. It is not suitable for legal evidence, workplace compliance, or noise complaints that need certified equipment.
Frequently asked questions
How many decibels is a normal conversation?
About 60 dB at one metre. Quiet rooms are around 30 to 40 dB and busy traffic is around 70 to 85 dB.
What is dBA?
It is a decibel level weighted to match how humans hear, giving less importance to very low and very high frequencies.
Why is a decibel scale logarithmic?
Because hearing responds to ratios of sound pressure. An increase of 10 dB is a tenfold increase in sound energy and sounds roughly twice as loud.
Can I use my phone to check workplace noise?
Only as a rough guide. Workplace regulation requires calibrated, standards-compliant meters.
Why do two phones give different readings?
Their microphones and software differ. Use the offset to match a reference meter.